Eagle Transporter in Solidworks, new stuff last page :-)

Reply

Re: Rebuilding the Eagle Transporter in Solidworks#344547

By tom - Wed Jul 06, 2011 4:51 pm

- Wed Jul 06, 2011 4:51 pm #344547

I guess you're using aniso on the exhaust but only a single value, right? How are they ment to look?

Next Limit Team

Re: Rebuilding the Eagle Transporter in Solidworks#344552

By NicoR44 - Wed Jul 06, 2011 6:08 pm

- Wed Jul 06, 2011 6:08 pm #344552

Actually it's just cobalt from the wizard, with roughness set to 20, and ref 0 changed a bit on both bsdf layers.
It should look like this:

http://www.smallartworks.ca/Articles/Re ... tore4.html

Last edited by NicoR44 on Thu Jul 07, 2011 11:08 pm, edited 1 time in total.

Curt Roth, formally known as NicoR44.

Re: Rebuilding the Eagle Transporter in Solidworks#344571

By Hervé - Thu Jul 07, 2011 7:52 am

- Thu Jul 07, 2011 7:52 am #344571

ahah almost fell of my chair.. pheww.. just a photo hervé.. just a photo... calm down.. hihi.. although I am sure you can even do a better job..

sing with me.... la la la... la la la

Re: Rebuilding the Eagle Transporter in Solidworks#344574

By NicoR44 - Thu Jul 07, 2011 9:34 am

- Thu Jul 07, 2011 9:34 am #344574

hehehe, yeah I wish

Curt Roth, formally known as NicoR44.

Re: Rebuilding the Eagle Transporter in Solidworks#344575

By Hervé - Thu Jul 07, 2011 9:59 am

- Thu Jul 07, 2011 9:59 am #344575

look at the past... Holland has the best painters and illustrators in the world.. back from the 16 century... and you're no exception..

so yes... I believe you can do it.. and not only do it.. but a mile better !!.. yes sir

sing with me.... la la la... la la la

Re: Rebuilding the Eagle Transporter in Solidworks#344576

By macray - Thu Jul 07, 2011 11:12 am

- Thu Jul 07, 2011 11:12 am #344576

Hervé wrote:look at the past... Holland has the best painters and illustrators in the world.. back from the 16 century... and you're no exception.. so yes... I believe you can do it.. and not only do it.. but a mile better !!.. yes sir

don't expect him to get rid of a body part, though...

Cinema4D Studio MSA, MoI 14+1+1

Re: Rebuilding the Eagle Transporter in Solidworks#344580

By Hervé - Thu Jul 07, 2011 12:09 pm

- Thu Jul 07, 2011 12:09 pm #344580

sing with me.... la la la... la la la

Re: Rebuilding the Eagle Transporter in Solidworks#344589

By NicoR44 - Thu Jul 07, 2011 3:30 pm

- Thu Jul 07, 2011 3:30 pm #344589

Curt Roth, formally known as NicoR44.

Re: Rebuilding the Eagle Transporter in Solidworks#344617

By NicoR44 - Fri Jul 08, 2011 12:19 pm

- Fri Jul 08, 2011 12:19 pm #344617

Curt Roth, formally known as NicoR44.

Re: Rebuilding the Eagle Transporter in Solidworks#344618

By djflod - Fri Jul 08, 2011 12:21 pm

- Fri Jul 08, 2011 12:21 pm #344618

i like

Re: Rebuilding the Eagle Transporter in Solidworks#344645

By NicoR44 - Sat Jul 09, 2011 12:54 am

- Sat Jul 09, 2011 12:54 am #344645

cheers !!

Curt Roth, formally known as NicoR44.

Re: Rebuilding the Eagle Transporter in Solidworks#344647

By rusteberg - Sat Jul 09, 2011 6:00 am

- Sat Jul 09, 2011 6:00 am #344647

The little cockpit module rocks!

What is your lighting setup if you don't mind me asking? Are you using studio hdr's through IBL only?

Edit: the mesh precision is awesome!