All posts relating to Maxwell Render 1.x
By FredSpeaks
#107684
mverta wrote:Man, we gotta give you guys something else to do...

;)


_Mike
And soon!?! :D
User avatar
By mverta
#107694
My pre-release announcement posting has been submitted for review.

Stay tuned.

_Mike
Last edited by mverta on Fri Jan 13, 2006 4:38 am, edited 1 time in total.
User avatar
By Jozvex
#107697
*trembles with anticipation and yet puts on a falsely calm appearance as to not alert the other forum members of his true mental state*

:D
User avatar
By kivimaki
#107714
:: :x RC5 ANGST :x ::

Must... Have... RC5...

The weightmapping would make this project so much easier!
User avatar
By Hervé
#107725
well.... dunno about Spain... but Private Co over there are worse than public administration... one auhorization here... one copy proof there... jeeez is NL also the post office in Madrid... :wink:
User avatar
By janosch1234
#107763
mverta wrote:
Hervé wrote:have you had the official ok from the officials... :wink:
I haven't written it yet; I want to wait until I'm absolutely sure what's going to be in the release. At this stage, a lot of things get turned on and off many times and so the version I'm rendering with tonight may be different than the one tomorrow morning. As soon as I hear that our current build is locked, I'll author the post and submit it for review.

_Mike
mverta wrote:My pre-release announcement posting has been submitted for review.

Stay tuned.

_Mike
So the current build is locked now...
But what does that mean exactly?

btw. Mike, thanks for your effort.
User avatar
By Maximus3D
#107765
If i can suggest for those public announcements when those are written is that whatever features are currently disabled in the release we will get is listed in the announcement so we're prepared and that we know that in advance and then the amounts of complaints from users noticing that this or that feautre is disabled or not yet implemented will be reduced. Just a suggestion as i think it would be wise to do so.

/ Max
User avatar
By aitraaz
#107777
mverta wrote:My pre-release announcement posting has been submitted for review.

Stay tuned.

_Mike
Good news. The only thing that sounds strange here is when you say things like 'half are gonna like it and half are gonna prefer the beta.' I mean, if the RS1+ engine is an all around improvement of the beta, why are half still gonna prefer the beta? The usual studio interface complaints? Are we missing something here? Guess we'll find out soon. Thnx...
User avatar
By psanitra
#107781
I hope we`ll find it today, it`s friday, you know.. :D
User avatar
By Jozvex
#107786
Maximus3D wrote:If i can suggest for those public announcements when those are written is that whatever features are currently disabled in the release we will get is listed in the announcement so we're prepared and that we know that in advance and then the amounts of complaints from users noticing that this or that feautre is disabled or not yet implemented will be reduced.
That suggestion has the right intentions, however Mike has mentioned a few times that throughout a single day of testing, different features are turned on and off many times. So unless they only ever make announcements right before a new version is released, it may just cause more trouble. They might announce "yadda yadda yadda but emitters are disabled." and everyone would freak out, only for emitters to be turned back on 30 minutes later.
User avatar
By stonelli
#107796
mverta wrote:My pre-release announcement posting has been submitted for review.

Stay tuned.

_Mike
Good to hear this, it is getting tiring to wait....
By Maya69
#107820
mverta , juan , tom, victor

just a little question

rc5 release for this day ?
By giacob
#107876
u know what the most amazing thing is?.... everytime u start praising them because they have opened a good communication channell. then after a while all forms of communications disappeare all of a sudden !!!!dont know what to think..... :roll: :cry:
  • 1
  • 39
  • 40
  • 41
  • 42
  • 43
  • 57
render engines and Maxwell

"prompt, edit, prompt" How will an AI r[…]